Top 10 typical forklift crashes ， forklift procedure must take notice of these issues ！.

Don't underestimate the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are many accidents involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The size of the forklift freight surpasses the permitted width of the route and holds on the roadside rack, which nearly triggers an accident.
Case 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a seat belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure ought to take note of these issues ：.

Begin.
1. Prior to beginning, observe the surroundings, and after validating that there are no challenges that prevent the security of driving, honk the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be risk-free before beginning.
3. When the forklift starts with a tons, the driver must first validate that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork needs to not be elevated too high, which will impact the security of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving setting prior to driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will cause the car to lose side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it must obey the web traffic rules in the factory and need to maintain a specific safety and security range from the lorry ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be effectively slanted back. The lots will not be increased except when stacking or loading. .
8. The height of the load must not obstruct the motorist's view. In special situations, when the item affects the forward vision, drive at a low rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to base on the fork to hold products and play a balancing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never run with ailments or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks need to be changed as needed to make the lots of the two forks balanced and not manipulated, and one side of the item need to be against the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or draw. In special scenarios, security indication should be established to remind bordering pedestrians. .
3. In the process of packing and dumping products, the forklift must be stopped with the brake. .
4. The rate of the car need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork should be as deep as feasible under the lots, and it ought to be kept in mind that the fork suggestion must not touch other products or things. The load must be maintained with Stand-on Electric Pallet Stacker minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead a little when the lots is lowered to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and ram tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise workers to engage in high-altitude operations to prevent high-altitude falling mishaps. .
9. It is not permitted to make use of the brake inertia to slide, place, round or roll things. .
10. It is not allowed to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are Stand-on Electric Pallet Stacker in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork framework.
2. Draw the emergency brake manage to dead or dispirit the emergency brake button.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage should additionally be examined and the seals must be replaced in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the vehicle;.
2. When you encounter a person before you during driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the slope is enabled.
7. Do not drive across the slope. When the gradient is more than 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they run into big or hefty goods and most likely to the driver's line of vision, they should take the reversing workout
.
The "Eight Prohibitions" ought to be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not allowed to use stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844